ctrace(1) ctrace(1)NAME ctrace - debugs a C program SYNOPSIS ctrace [-b] [-e] [-ffunctions] [-ln] [-o] [-p `s'] [-P] [-rf] [-s] [-tn] [-u] [-vfunctions] [-x] [file] ARGUMENTS -b Uses only basic functions in the trace code, that is, those in ctype(3C), printf(3S), and string(3C). These are usually available even in cross-compilers for microprocessors. In particular, this option is needed when the traced program runs under an operating system that does not have signal(3), fflush(3S), longjmp(3C), or setjmp(3C). -e Specifies the floating point format. -ffunctions Traces only these functions. -ln Checks n consecutively executed statements for looping trace output, instead of the default of 20. Use 0 to get all the trace output from loops. -o Specifies the octal format. -p `s' Changes the trace print function from the default of `printf('. For example, `fprintf(stderr' would send the trace to the standard error output. -P Runs the C preprocessor on the input before tracing it. You can also use the -D, -I, and -U cc(1) preprocessor options. -rf Uses file f in place of the runtime.c trace function package. This lets you change the entire print function, instead of just the name and leading arguments (see the -p option). -s Suppresses redundant trace output from simple assignment statements and string copy function calls. This option can hide a bug caused by use of the = operator in place of the == operator. -tn Traces n variables per statement instead of the default of 10 (the maximum number is 20). The ``Status Messages and Values'' section explains when to use this option. -u Specifies the unsigned format. January 1992 1
ctrace(1) ctrace(1)-vfunctions Traces all but these -x Specifies the hexadecimal format. file Specifies the file to be debugged. If this argument is not given, ctrace will read the file from the standard input. DESCRIPTION ctrace allows you to follow the execution of a C program, statement by statement. The effect is similar to executing a shell procedure with the -x option. The ctrace command reads the C program in file (or from standard input if you do not specify file), inserts statements to print the text of each executable statement and the values of all variables referenced or modified, and writes the modified program to the standard output. You must put the output of ctrace into a temporary file because the cc(1) command does not allow the use of a pipe. You then compile and execute this file. As each statement in the program executes, it will be listed at the terminal, followed by the name and value of any variables referenced or modified in the statement, followed by any output from the statement. Loops in the trace output are detected and tracing is stopped until the loop is exited or a different sequence of statements within the loop is executed. A warning message is printed every 1000 times through the loop to help you detect infinite loops. The trace output goes to the standard output, so that you may put it into a file for examination with an editor or the bfs(1) or tail(1) commands. You may want to print variables in other formats besides the default. Long and pointer variables are always printed as signed integers. Pointers to character arrays are also printed as strings if appropriate. char, short, and int variables are also printed as signed integers and, if appropriate, as characters. Double variables are printed as floating point numbers in scientific notation. EXAMPLES If the file lc.c contains this C program: 1 #include <stdio.h> 2 main() /* count lines in input */ 3 { 4 int c, nl; 5 6 nl = 0; 7 while ((c = getchar()) != EOF) 8 if (c = '\n') 2 January 1992
ctrace(1) ctrace(1)9 ++nl; 10 printf("%d\n", nl); 11 } and you enter these commands and test data: cc lc.c a.out 1 the program will be compiled and executed. The output of the program will be the number 2, which is not correct because there is only one line in the test data. The error in this program is common, but subtle. If you invoke ctrace with these commands: ctrace lc.c > temp.c cc temp.c a.out the output will be: 2 main() 6 nl = 0; /* nl == 0 */ 7 while ((c = getchar()) != EOF) The program is now waiting for input. If you enter the same test data as before, the output will be: /* c == 49 or '1' */ 8 if (c = '\n') /* c == 10 or '\n' */ 9 ++nl; /* nl == 1 */ 7 while ((c = getchar()) != EOF) /* c == 10 or '\n' */ 8 if (c = '\n') /* c == 10 or '\n' */ 9 ++nl; /* nl == 2 */ 7 /* repeating */ If you now enter an end-of-file character (CONTROL-d), the final output will be: /* c == -1 */ 10 printf("%d\n", nl); /* nl == 2 */2 /* return */ January 1992 3
ctrace(1) ctrace(1)Note that the program output printed at the end of the trace line for the nl variable. Also note the return comment added by ctrace at the end of the trace output. This shows the implicit return at the terminating brace in the function. The trace output shows that variable c is assigned the value ``1'' in line 7, but in line 8 it has the value ``\n''. Once your attention is drawn to this if statement, you will probably realize that you used the assignment operator (=) in place of the equal operator (==). During code reading, it is easy to miss this error. Execution-time Trace Control The default operation for ctrace is to trace the entire program file, unless you use the -f or -v options to trace specific functions. This does not give you statement by statement control of the tracing, nor does it let you turn the tracing off and on when executing the traced program. You can do both of these by adding ctroff and ctron function calls to your program to turn the tracing off and on, respectively, at execution time. Thus, you can code arbitrarily complex criteria for trace control with if statements, and you can even conditionally include this code because ctrace defines the CTRACE preprocessor variable. For example: #ifdef CTRACE if (c == '!' && i > 1000) ctron(); #endif You can also call these functions from sdb(1) if you compile with the -g option. For example, to trace all but lines 7 to 10 in the main function, enter: sdb a.out main:7b ctroff() main:11b ctron() r You can also turn the trace off and on by setting the static variable tr_ct_ to 0 and 1, respectively. This is useful if you are using a debugger that cannot call these functions directly. STATUS MESSAGES AND VALUES This section contains messages from both ctrace and cc(1), since the traced code often gets some cc warning messages. You can get cc error messages in some rare cases, all of which can be avoided. 4 January 1992
ctrace(1) ctrace(1)ctrace Messages Warning: some variables are not traced Only 10 variables are traced in a statement to prevent the C compiler ``out of tree space; simplify expression'' error. Use the -t option to increase this number. Warning: statement too long to trace This statement is over 400 characters long. Make sure that you are using tabs to indent your code, not spaces. Cannot handle preprocessor code, use -P This is usually caused by #ifdef/#endif preprocessor statements in the middle of a C statement, or by a semicolon at the end of a #define preprocessor statement. ``if ... else if'' sequence too Split the sequence by removing an else from the middle. Possible syntax error, try -P option Use the -P option to preprocess the ctrace input, along with any appropriate -D, -I, and -U preprocessor options. If you still get the error message, check the WARNINGS section below. cc Messages Warning: floating point not implemented Warning: illegal combination of pointer and Warning: statement not reached Warning: sizeof returns 0 Ignore these messages. Compiler takes size of function See the ctrace ``possible syntax error'' message above. yacc stack overflow See the ``ctrace `if ... else if' sequence message, above. Out of tree space; simplify expression Use the -t option to reduce the number of traced variables per statement from the default of 10. Ignore the ``ctrace: too many variables to trace'' warnings you will now get. redeclaration of signal Either correct this declaration of signal(3), or remove it and #include <signal.h>. January 1992 5
ctrace(1) ctrace(1)WARNINGS You will get a ctrace syntax error if you omit the semicolon at the end of the last element declaration in a structure or union, just before the right brace (}). This is optional in some C compilers. Defining a function with the same name as a system function may cause a syntax error if the number of arguments is changed. To fix this, just use a different name. The ctrace command assumes that BADMAG is a preprocessor macro, and that EOF and NULL are #define d constants. Declaring any of these to be variables, e.g., int EOF will cause a syntax error. LIMITATIONS The ctrace command does not know about the components of aggregates like structures, unions, and arrays. It cannot choose a format to print all the components of an aggregate when an assignment is made to the entire aggregate. The ctrace command may choose to print the address of an aggregate or use the wrong format (e.g., %e for a structure with two integer members) when printing the value of an aggregate. Pointer values are always treated as pointers to character strings. The loop trace output elimination is done separately for each file of a multi-file program. This can result in functions called from a loop still being traced, or the elimination of trace output from one function in a file until another in the same file is called. FILES /usr/bin/ctrace Executable file /usr/lib/ctrace Directory containing source files SEE ALSO sdb(1) ctype(3C), fclose(3S), printf(3S), setjmp(3C), signal(3), string(3C) in A/UX Programmer's Reference 6 January 1992